Crown CTS 2000
Crown CTS 2000 Crown CTS 2000 Description: Building on the foundation of the Com-Tech® Series, Crown's CTs Series offers new flexibility and value for installed sound applications. The Com-Tech Series were the first to offer independent selection of high- and low-impedance operation for a specific channel, and CTs Series amplifiers continue that tradition, with power levels and features carefully chosen to perfectly integrate into fixed install design requirements. Crown CTS 2000 Output Power: 2-ohm Stereo (Per Channel): 1000W 4-ohm Stereo (Per Channel): 1000W 8-ohm Stereo (Per Channel): 1000W 16-ohm Stereo (Per Channel): 625W 70V Stereo (Per Channel): 1000W 100V Stereo (Per Channel): 1000W 4-ohm Bridged-Mono: 2000W 8-ohm Bridged-Mono: 2000W 16-ohm Bridged-Mono: 2000W 140V Bridged-Mono: 2000W 200V Bridged-Mono: 2000W Crown CTS 2000 Features: High power density. All two channel models and four channel model in a 2RU chassis, eight channel model in a 3RU chassis Crown Switching Power Supply for lighter weight Selectable "Constant-Voltage" or low-impedance (4/8 ohm) operation per channel on 2-channel models, and per channel-pair on 4-and 8-channel models 100V direct outputs on CTs 2000, CTs 3000, CTs 4200, and CTs 8200 Legendary Crown class-I (BCA) and AB+B output topologies offer the best in amplifier reliability 4- and 8-channel models offer perfect independent power solutions for multi-zoned systems· "FIT" (Fault Isolation Topology) circuitry on 4- and 8-channel models isolates fault conditions without affecting neighboring channels Comprehensive array of indicators provide accurate diagnostics Two-channel models are fully PIP2-compatible. Multi-channel models accept MC accessory modules. HiQnet - compatible. Crown CTS 2000 Specifications: Frequency Response (at 1 watt, 20 Hz - 20 kHz): ± 0.25 dB. Signal to Noise Ratio below rated power (20 Hz to 20 kHz): 105 dB A-weighted. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: CTs 600/1200:"Damping Factor: 10 Hz to 100 Hz: > 3000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): 50 dB. DC Output Offset: Input Impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced. Maximum Input Level: +20 dBu before input compression, +32 dBu absolute maximum. Load Impedance (Note: Safe with all types of loads): CTs 600/1200: Stereo: 2/4/8/16 ohms, 70V." Bridge Mono: 4/8/16 ohms, 140V. CTs 2000/3000: Stereo: 2/4/8/16 ohms, 70V, 100V." Bridge Mono: 4/8/16 ohms, 140V, 200V. Voltage Gain (at maximum level setting): 8/4 ohm operation, 1.4V sensitivity CTs 600 35:1 (31 dB) CTs 1200 50:1 (34 dB) CTs 2000 63.9:1 (36 dB) CTs 3000 71.4:1 (37 dB) 26 dB: 20:1 (26 dB). 70V operation, 1.4V sensitivity or 100V operation, 2.0V sensitivity: 50:1 (34 dB). Required AC Mains (+15%, -25%): 120V/60 Hz, 230V/50 Hz. Power Draw at Idle (120VAC mains): CTs 600/1200: 24W (standby mode) CTs 2000/3000: 3